Laforge Doors

 
 
 

Our Products > Commercial Doors > SERVICE DOORS

SERVICE DOORS
 
Clopay-GoldBar_RGB.png

 

 

Serving the industry with an array of curtain materials (pre finished galvanized steel in gauges from 24 to 18, stainless, or aluminum), slat profiles, and colors, Clopay’s service doors can accommodate most openings and building requirements.


   CMDC-RSSDOOR-10.pdf

FEATURES & BENEFITS

SERVICE DOORS (CESD)

Service Doors (CESD) are manufactured from 2 5/8" wide metal slats roll formed to interlace together to create a continuous steel curtain. They are used to provide security against entry or weather protection at the exterior or interior openings in industrial, commercial, institutional and other buildings.

CESD10 STANDARD HEAVY DUTY SERVICE DOORS

Sizes: 30' wide, 30' high standard construction. Large openings to 50' wide, 40' high, consult factory.
Operation: Motors, chain, hand-crank or push-up designs based on size, weight or frequency of operation.
Usage: Standard construction is up to 20 cycles per day with High Cycle Construction available for doors expected to be operated more than 20 cycles per day, i.e. parking garages, sally ports.
Fast Acting Doors: For high traffic openings or where air flow or temperature control is critical, doors can be designed to operate at more than twice the speed of typical doors, or up to 2 ft./sec.
Wind Load: Doors can be configured to withstand the full range of specific wind load requirements including missile impact ratings. Also, refer to WindCode Section.
Seismic Performance Validation:                                                                               Specific seismic calculations can be provided for all doors that are mounted Face of Wall or Between Jambs to steel or masonry. Seismic performance validation as per ASCE 7-05.
Materials & Finishes: Standard door curtains are available in 24, 22, 20 and 18 gauge galvanized steel in light gray, white or tan. Also 20 gauge 300 series stainless steel with # 4 finish or #16 B&S gauge aluminum with a mill, clear or color anodized finish.
Locks: Wall mounted chain keeper or zinc plated steel slide bolt with padlock provisions
Operation: Chain hoist is standard; motor or manual operation is optional
Colors: White, gray, tan
Warranty: 2-year warranty against defects in materials and workmanship

 

CESD20 INSULATED HEAVY DUTY SERVICE DOORS 

Sizes: 30' wide, 30' high standard construction. Large openings to 50' wide, 40' high, consult factory.
Operation: Motors, chain, hand-crank or push-up designs based on size, weight or frequency of operation.
Usage: Standard construction is up to 20 cycles per day with High Cycle Construction available for doors expected to be operated more than 20 cycles per day, i.u. parking garages, sally ports.
Fast Acting Doors: For high traffic openings or where air flow or temperature control is critical, doors can be designed to operate at more than twice the speed of typical doors, or up to 2 ft./sec.
Wind Load: Doors can be configured to withstand the full range of specific wind load requirements including missile impact ratings. Also, refer to Wind Code Section.
Seismic Performance Validation: Specific seismic calculations can be provided for all doors that are mounted Face of Wall or Between Jambs to steel or masonry. Seismic performance validation as per ASCE 7-05.
Materials & Finishes: Exterior and interior slats are ASTM A 653 galvanized steel with an exclusive finish in light gray, tan or white (available 24/24 ga only). Powder coated finish is optional. The exterior skin is available in 24, 22, 20 and 18 gauge with combination exterior and interior slats being - 24/24, 22/24, 20/24, 18/24 and 22/22. Exterior and interior skins are also available in 22 gauge 300 series stainless steel with #4 finish and #18 B&S gauge aluminum with a mill, clear or color anodized finish.

 

SMOKE RATED DOORS (CERD)

Fire Doors (CERD) are available insulated and non-insulated, provide automatic closing in the event of fire detection with governed speed control. Fire doors also designed for use as a service door to provide security and access control in openings that are not part of a required means of egress.

CERD10 STANDARD HEAVY DUTY FIRE RATED DOORS

Listings:

UL Classified for fire protection and the loss of property and also UL, "S" leakage rated assembly labeled for smoke and draft control.

SmokeShield products meet the requirements of the International Building Code, 2006, Section 715.4.3. for Smoke-and-Draft Control Door Assemblies

Tested per UL 1784, the procedure for smoke-and-draft control door assemblies. Meets the requirements of NFPA 105

Sizes: 30' wide, 25' high standard construction. Large openings to 34' wide, consult factory.
Wind Load: Doors can be designed to meet specific PSF wind Load requirements.
Seismic Performance Validation:  Specific seismic calculations can be provided for all doors that are mounted Face of Wall or Between Jambs to steel or masonry. Seismic performance validation as per ASCE 7-05.
Materials & Finishes: Exterior/Interior curtain skin - galvanized steel in light gray or tan or optional powder coating is available. 300 series stainless steel with #4 finish. Cast iron end locks/wind locks are required per UL procedure. Click HERE for additional Material and Finishes information.
Mounting: The face of the wall or between jambs in both interior and exterior walls. Approved wall types for the mounting of fire doors include masonry or structural steel jambs.
Operation: Motor, chain or crank operating systems are recommended for ease of testing and controlled automatic closing speed.

 


CERD21 INSULATED HEAVY DUTY FIRE & SMOKE RATED DOOR

Listings: UL Classified 4HR, 3HR, 1 1/2HR, 3/4HR classified labels. Flame spread and smoke development index factors for the insulated fire doors mineral wool insulation are zero.
Sizes: 30' wide, 22' high standard construction. Large openings to 34' wide, consult factory.
Wind Load: Doors can be designed to meet specific PSF wind Load requirements.
Seismic Performance Validation: Specific seismic calculations can be provided for all doors that are mounted Face of Wall or Between Jambs to steel or masonry. Seismic performance validation as per ASCE 7-05.
Materials & Finishes: Exterior/Interior curtain skin - galvanized steel in light gray or tan or optional powder coating is available. 300 series stainless steel with #4 finish. Cast iron end locks/wind locks are required per UL procedure. 
Mounting: The face of the wall or between jambs in both interior and exterior walls. Approved wall types for the mounting of fire doors include masonry or structural steel jambs.
Opération: Motor, chain or crank operating systems are recommended for ease of testing and controlled automatic closing speed.


Copyright © 2017 Laforge Garage Door Inc All Rights Reserved.
Designed by Concept J MULTIMEDIA Inc. Managed by 123Clik ©